Precīzs piegādes termiņš norādīts augstāk un tiek aprēķināts katrai precei individuāli. Piegāde klientam ir bez maksas.
Apraksts
Trumpai apie prekę
Prekė: Oro filtro komplektas WANAS 350/2, 350/3, 355 COMBO, 430/630, G4, 4 vnt.. Kategorija: Dalys.
- Gamintojas: FILTR AIR
- Modelis: FILTR-AIR
G4 FILTER FOR VANAS RECUPERATORS
- A set of 4 G4 air filters for selected WANAS recuperators.
- The G4 filter is used for pre-filtration of air. It helps to retain dust, dust and larger particles of contaminants, supporting the proper operation of the ventilation system.
FITS WANAS RECUPERATORS:
• WANS 350 V/2
• WANES 350 H/2
• WANS 350 V/3
• WANS 350 H/3
• WANS 355 V_XF
• WANES 355 H_XF
• WANAS COMBO 430
• WANAS COMBO 430 Prestige XF
• WANAS COMBO 430 Light XF
• WANAS COMBO 630
• WANAS COMBO 630 Prestige XF
• WANAS COMBO 630 Light XF
- The manufacturer WANAS indicates the G4 filter for 350 V/2, 350 H/2, 350 V/3, 350 H/3, 355 and COMBO 430/630 control panels.
📦 CONTENTS OF THE SET
4 × air filter G4
You buy a complete set of 4 filters.
📏 DIMENSIONS OF 1 FILTER
• length: 480 mm
• width: 190 mm
• height: 5 mm
⚙ TECHNICAL PARAMETERS G4 (EU4)
• Mat thickness: 10,0 ± 2,0 mm
• Surface weight: 250 ± 25 g/m²
• Color: white
• Flammability feature: self-extinguishing
• Efficiency of dust extraction against mineral dust ASHRAE 52/76: η ≥ 65%
• Temperature resistance: up to 100°C with continuous operation
• Material ignition resistance: F1 according to DIN 53438
• Moisture and acid resistance: YES
🌬 FOR RECUPERATION OF VANAS
- Filters are designed for selected WANAS ventilation units.
- Before buying compare the model of your control panel and the dimensions of the filter with those given in the offer. 📋
- A set of 4 G4 filters is a convenient supply for regular replacement of filters in the recuperator. 🔄🏠
WHEN IS IT WORTH REPLACING THE FILTER?
Regular replacement of filters helps maintain proper operation of the recuperator and proper air quality. 🌬
WANAS recommends replacing filters every 180 days, while every 90 days it is worth checking their condition and vacuuming them.
The filter should be replaced earlier if:
• the filter is heavily soiled or dusty 🧹
• noticeably reduced air flow
• recuperator works louder than usual
• the device works less efficiently
• a large amount of dust and debris is visible on the filter
• recuperator displays a message about the need to replace the filter ⚠
- Remember: the frequency of replacement may depend on the conditions of use, air quality in the area, the season and the amount of pollution.
- Regularly control the condition of the filters and replace them when they are heavily soiled.
HIGH QUALITY OF WORKMANSHIP
• Polish product 🇵🇱
• Durable and effective performance
• Stable and durable construction
• Filter mat trimmed on a frame made of steel wire with a thickness of 4 mm
• Design adapted for regular replacement in recuperators
🏠 WHERE CAN FILTERS BE USED?
G4 filters can be used in ventilation systems m.in. in:
• apartments
• homes
• utility facilities
• industrial buildings
WHY CHOOSE THIS FILTER?
✅ Effective pre-filtering
It helps to retain dust, leaves, insects, dander, sand and larger debris. WANAS indicates the G4/ISO COARSE 75% class as pre-filtration for its control panels.
🌬 Proper airflow
A clean filter supports the smooth operation of the recuperator and helps maintain proper ventilation.
🏠 Better protection of the control panel
The filter stops larger contaminants before they get further inside the device.
🇵🇱 Polish product
FILTR AIR brand filter, made of durable filter mat and mounted on a steel frame.
📦 4 pieces included
You buy a set of 4 filters, so you have a spare for your next replacement.
🔄 Practical solution for regular replacement
Regular inspection and replacement of the dirty filter helps to maintain the smooth operation of the ventilation system.
Clean filter = more efficient ventilation, better recuperator protection and comfort of use.
HOW TO REPLACE THE FILTER YOURSELF?
Replacing the filter in the recuperator is simple and you can do it yourself, without calling for service. 👍
1 Turn off recuperator
Before starting the replacement, turn off the device and, for safety, disconnect it from the power supply.
2 Open access to filters
Open the cover or service door of the recuperator according to the instruction manual of your model.
3 Remove the used filter
Carefully slide the dirty filter out of the guide. If it is heavily dusty, it is worth doing it slowly, so as not to spill the accumulated impurities.
4 Clear installation site 🧹
Before inserting a new filter, you can gently remove dust from the guides and filter chamber.
5 Insert new filter G4 🌬
Place the new filter in the right place, paying attention to its correct position and direction of air flow, if it is marked.
6 Close cover
Make sure that the filter is correctly in the guide and the service cover is tightly closed.
7 Enable recuperator ✅
After installing the filter, start the device and check that it is working properly.
HINT!
It is worth saving the date of filter replacement. This makes it easier to control when another exchange is approaching. Control the condition of the filter regularly, especially if the recuperator works in a place with a large amount of dust or debris. 🌬 🏠
Replacing the filter takes little time, and regular inspection helps maintain proper ventilation.
AS THEY ARE
HINT!
It is worth saving the date of filter replacement. This makes it easier to control when another exchange is approaching. Control the condition of the filter regularly, especially if the recuperator works in a place with a large amount of dust or debris. 🌬 🏠
Replacing the filter takes little time, and regular inspection helps maintain proper ventilation.
❓ MOST COMMON QUESTIONS
1. Does the filter fit my WANAS recuperator?
The filter fits selected models WANAS 350 V/2, 350 H/2, 350 V/3, 350 H/3, 355 and COMBO 430 and COMBO 630. Before buying, it is worth comparing the model of the control panel and the dimensions of the filter. (WAS)
2. How often should I change the filter?
The filter should be regularly checked and replaced depending on the degree of dirt and the conditions of use of the recuperator. A heavily soiled filter should be replaced earlier.
3. Can I replace the filter myself?
Yes. Replacing the filter is a simple activity that you can do yourself. Before replacing, turn off the recuperator and disconnect the device from the power supply. After replacement, you need to check the correct position of the filter and the exact closing of the door. (WAS)
4. What does regular filter replacement mean?
A clean filter helps retain dust, leaves, insects, dander, sand and larger debris and supports proper airflow and recuperator operation. (WAS)
5. How many filters will I get in the set?
The set includes 4 pieces of G4 filters, so you have a spare for your next replacements. 📦
HINT!
It is worth saving the date of filter replacement. This makes it easier to control when another exchange is approaching. Control the condition of the filter regularly, especially if the recuperator works in a place with a large amount of dust or debris. 🌬 🏠
Replacing the filter takes little time, and regular inspection helps maintain proper ventilation.
Specifications
| Group | Name | Value |
|---|---|---|
| Parametry | Condition | new |
| Parametry | Invoice | With a VAT invoice |
| Parametry | Brand | FILTR AIR |
| Parametry | Kind | filter |
| Parametry | Manufacturer code | FILTR-AIR |
| Parametry | Packaging status | original |
| Parametry | Batteries included | no |



