Pašpielīmējoša aizsargplēve pret skrāpējumiem MAX, 140x60 cm, biezāka

Trumpai apie prekę

Prekė: Savitvirtė apsauginė plėvelė nuo įbrėžimų MAX, 140x60 cm, storesnė. Kategorija: Draskyklės.

• Gamintojas: Clean Protect
• Modelis: 5904800273761
• Spalva: other

Self-adhesive film for furniture – the largest selection of sizes.

The protective sticker perfectly protects doors and furniture from the claws of cats and dogs!

Does your cat love sharpening claws on the edges of the couch? Or does the dog scratch the door every time he wants to go outside or home?

Clean Protect Pet is an effective protection of furniture against scratches by a cat or dog. Secure the corners of sofas, armchairs, doors or other surfaces.

Self-adhesive, transparent protective film will easily help protect home furnishings.

Colorless protective film for doors, furniture, walls

Strong adhesive is also safe for varnished or upholstered furniture surfaces.

The film after removal leaves no traces.

If desired, the film can be easily cut with scissors or a wallpaper cutter to the desired size.

- Inner mesh panties

• Size: 140 x 60 cm
• Color: almost transparent (transparent)
• Type: self-adhesive
• Material: PCV

8x upholstery pins for free

We add 8 pieces of upholstery pins to each film. Thanks to this, the film will be even more firmly attached to the material surfaces.

Greater strength compared to 140 micrometer thick films available at other auctions!

Thickness: 170 microns (0,17mm) – thick enough to protect the surface from claws and thin enough that you can hardly see it!

Self-adhesive protective cap Clean Protect Pet to:

• easy and quick installation - self-adhesive
• odorless
• practically invisible - does not cover the surface
• thickness: 170 microns (0,17mm)
• safe - does not allergize
• resistant to detergents
• protects against surface scratches
• no traces after removal
• application temperature: min +8°C
• application temperature -40 - +80°C
• Anti-slip - anti-slip certificate R11 DIN51130
• anti-flammable - non-flammability certificate B1 DIN4102

Assembly instructions:

Dry gluing

(requires more practice due to the inability to peel off and re-stick the film if correction is necessary)

Recommended tools:

• Clean Protect IZO universal degreaser,
• squeegee.

1a) Surface (floor, stairs, windows, doors, etc. ) should be cleaned dry and then degreased with a cloth soaked with degreasing agent, e.g.: Clean Protect IZO available at our auctions.

It should be remembered to test the effect of the preparation on a small, invisible fragment of the glued surface.

2a) We gradually remove the protective paper and Clean Protect overlays from the shorter side by gradually peeling off the tape.

3a) The surface of the film is leveled with a cloth or squeegee (available at our auctions). If air bubbles form, they can be pierced with a needle.

4a) Ready!

Wet gluing

(allows correction of the position of the film, recommended especially in the case of wrapping larger areas)

Recommended tools:

• Clean Protect IZO universal degreaser,
• liquid for application of Clean Protect WET film,
• squeegee,
• paper towels.

1b) Surface (floor, stairs, windows, doors, etc. ) should be cleaned dry and then degreased with a cloth soaked with degreasing agent, e.g.: Clean Protect IZO available at our auctions.

• It should be remembered to test the effect of the preparation on a small, invisible fragment of the glued surface.

2b) Spray abundantly and evenly with Clean Protect WET liquid where the film will be applied.

• For wood surfaces, wood-like panels, etc. Remember to spray only places well protected against water penetration.

3b) We gradually remove the protective paper and put the film on a wet surface and put it in the right place.

4b) We smooth the film with a squeegee squeezing water from underneath, starting from the center towards the edges. Pay attention not to move the film. Wipe the water with a paper towel or absorbent cloth.

It is worth remembering:

- in the case of varnished surfaces, it is recommended to use overlays not earlier than about a week after varnishing. This is the time necessary to completely dry the varnish.

- in the case of using overlays on varnished surfaces, it is worth performing a test of varnish hardness by sticking and peeling off a small fragment of the overlay.

-before peeling off used overlays, it is worth heating the overlays (e.g. with a dryer) – glue residues can be removed with a cloth soaked, e.g.: Clean Protect label.

Safe delivery in cardboard tubes – the pad is well protected and is not exposed to damage and bending. In addition, the tubes are protected with stretch film to protect against rain/moisture during delivery of the package.

Specifications