Vandens siurblys su 100 l hidroforsu, 1100 W

Trumpai apie prekę

Prekė: Vandens siurblys su 100 l hidroforsu, 1100 W. Kategorija: Siurbliai ir hidroforai.

• Gamintojas: BG-INVEST
• Modelis: BG-K0001-100

➡ Tank capacity: 100 l

➡ Maximum pump capacity: 3600 l/h — 60 l/min

➡ Maximum lifting height: 50 m

➡ Engine power: 1100 W

➡ Power supply: 230 V

Looking for a powerful hydrophore kit that can provide stable water pressure in your home or garden? Our hydrophore 100 L with surface pump 1100W is a complete solution for the uptake of clean water from wells, tanks and other water intakes.

Thanks to the capacity of 3600 l/h, lifting height 50 m and the possibility of suction from a depth of up to 8 meters, the set is perfect for both daily power supply of the water system and watering the garden.

Hydrophore set for pumping clean, cold water will work well when supplying the house, plot and farm with water and when watering the garden.

When properly assembled and connected, the kit automatically starts and stops the pump depending on the pressure in the installation.

THE SET INCLUDES:

1. JX 1100 PUMP with cable and plug
2. TANK 100L
3. PRESSURE SWITCH
4. PRESSURE GAUGE
5. FIVE-WAY DISCHARGE OUTPUT
6. ANTI-VIBRATION HOSE

ADVANTAGES OF THE SET WITH TANK 100L - Farms, large installations, limiting frequent switching on of the pump.

The larger the tank:

• the pump starts less often,
• extends the life of the engine,
• pressure is more stable,
• energy consumption is lower.

• Application: Will this model be suitable?
• Single-family house: ✅ Yes
• Cottage: ✅ Yes
• Watering the garden: ✅ Yes
• Rainwater: ✅ Yes
• Pressure washer: ✅ Yes
• Drop irrigation: ✅ Yes
• Well dug: ✅ Yes (up to 8 m)
• Well drilled with water mirror over 8 m: ❌ Recommended submersible pump

✅ HYDROPHORE TANK 100L - CARBON STEEL

➡ Pressure water supply allows you to use the installation without starting the pump with every small intake.

➡ Restriction of switching frequency promotes quieter operation of the entire system.

➡ EPDM diaphragm

➡ Steel body with anti-corrosion coating and horizontal design with legs allow stable positioning of the set.

TECHNICAL DATA

➡ Maximum test pressure: 8 Bara

➡ Type of tank: Diaphragm

➡ Diaphragm : EPDM mounted in the tank

➡ Ready to assemble: Yes

➡ Tank orientation: Levels

➡ Tank capacity: 100l

➡ Connection thread size: 1"

➡ Painting: Powder

➡ CE certified: Yes

➡ Dimensions: L 71 x W 45 x H 47

➡ Carbon steel

➡ The tank complies with the strict requirements of Directive 2014/68/EU.

✅ ACCESSORIES ON A FIVE-WAY CONNECTION

➡ The five-way connection is mounted at the pump discharge output. It connects the pump to the fixture, tank and further part of the installation.

➡ The pressure switch and pressure gauge are screwed into the appropriate holes of the five-way connection.

➡ The anti-vibration hose connects the connection to the diaphragm tank.

➡ This arrangement provides access to the fixture during pressure control, adjustment and operation.

The equipment is designed for self-twisting. Before starting, you should properly seal the joints and check their tightness. Photos show the target appearance of the kit after assembly.

✅ PUMP SPECIFICATIONS

➡ Max capacity (l/min): 60

➡ Max capacity (m3/h): 3,6

➡ Lifting height (m): 48

➡ Suction capacity (m): 8

➡ Engine power (W): 1100

➡ Engine power (kW): 1,1

➡ Power Supply (V): 230

➡ Stub Size(inches): 1 x 1

Actual performance depends on water intake depth, pumping height and installation resistance.

✅ WORKING CONDITIONS

➡ Maximum water temperature: 35°C

➡ Maximum ambient temperature: 40°C

➡ Insulation Class: B

➡ Operating Mode: Continuous

➡ Degree of protection: IP 44

➡ Engine speed: 2850 rpm

1. Set the set on a stable substrate, in a dry place protected against frost.
2. Connect the suction hose, terminated with a suction basket with a check valve. Take care of the tightness of all connections.
3. Install pressure gauge and pressure switch — on a five-way connector or directly in the pump body, depending on the model. Seal the threads with Teflon tape or tows.
4. Connect the pump to the tank with the appropriate hose, and connect the discharge output to the receiving system.
5. Connect the pump to the pressure switch. The pump cable is cut into two sections: one comes out of the engine and the other is terminated with a plug. Enter both sections through the switch culverts. Connect L and N conductors from the motor to the pump terminals, and L and N conductors from the plug to the power terminals. Connect the yellow-green PE conductors of both sections to the protective clamps. Follow the scheme of the switch. Tighten clamps and culverts and close the housing. Do all the steps with the plug removed from the outlet.
6. Pour and vent the pump and suction hose, then start the kit and check the tightness and operation of the switch.

1. Turn off the pump and disconnect the power. Open the flood hole or connection shown in the illustration.
2. Fill the pump and suction line with clean water. Add slowly until the system is full and the water level stops dropping.
3. Close the flood hole tightly or restore the discharge connection if the flooding was carried out through a connector or a five-way connector.
4. Open the tap on the discharge side and start the pump. Observe the water flow and pressure gauge.
5. If the pump does not draw water, turn it off and flood the system again. Repeat the action if necessary. If the problem persists, check the tightness of the suction line and check valve.

IMPORTANT! Do not allow the pump to run dry. Pour and vent before the first start and after each longer break in use.

INCLUDED

✅ JX 1100 hydrophore pump with 50 cm cable

✅ pressure gauge and female pressure switch

✅ Power cable with 120m plug

✅ Anti-vibration hose with gasket

✅ Hydrophore tank 100L

✅ User Manual

Thanks to the possibility of connecting the hydrophore equipment into the pump body (one of the options), we save at the height of the entire set, which in many cases can be a huge advantage and ease of installation. Of course, such mounting of accessories is not mandatory. The fixture can also be installed on a water system, e.g. on a discharge pipe that goes to the mouth of the water. Such installation is possible using appropriate hydraulic components according to individual needs.

Example of a hydrophore kit connection scheme

1. Hydrophore pump
2. Diaphragm tank
3. Pump accessories with pressure switch
4. Suction tube
5. Anti-sand filter
6. Anti-sand filter valve
7. Check valve
8. Butterfly Nipple Ball Valve
9. Nipple ball valve with handle
10. Protection against dry running
11. Flood tee
12. Flow water filter
13. Pressure regulator with pressure gauge
14. PE coupling
15. PE pipe

Specifications