Oro sausintuvas–valytuvas, 20 l/24 val., iki 50 m², UV, WiFi

Trumpai apie prekę

Prekė: Oro sausintuvas–valytuvas, 20 l/24 val., iki 50 m², UV, WiFi. Kategorija: Oro sausintuvai.

• Gamintojas: Mission Air
• Modelis: COREDRY 20L/24h
• Galia: 380 W

✅capacity 20 l/24h

✅WiFi and Bluetooth control via the Mission Air app

✅ionization and UV lamp

✅automatic humidity control 35 to 90%

✅automatic defrosting

✅continuous drainage or tank 2,8 l

✅timer on and off

✅three fan speeds

✅parental lock

✅ecological refrigerant R290

COREDRY 20L is a home dehumidifier on wheels that removes excess moisture and protects the room from its effects. You set the target humidity in the range of 35 to 90%, and the device itself watches it around the clock. When the humidity in the room exceeds the setting, the compressor starts. When it falls below, the work is stopped and the Run light starts flashing. For faster air exchange, for example when drying laundry, you will choose the higher of the three fan gears or the ventilation mode itself.

You can collect condensate into a 2,8 liter tank with a level indicator visible from the outside and a protection that stops work after it is filled. If you prefer not to remember this, connect the hose and drain the water continuously to a constant drain. The round display on the front shows the current humidity, and you can set the work from the panel or from your phone, through the Mission Air application and the home WiFi network 2,4 GHz.

• Dehumidification capacity: 20 l / 24 h
• Power: 380 W
• Power supply: 220-240 V, 50-60 Hz
• Water tank capacity: 2,8 l
• Air flow: 160 m³/h
• Noise level: 43 dB
• Refrigerant: R290
• Humidity setting range: 35-90%
• Fan speeds: 3 (high, medium, low)
• Dimensions: 515 x 310 x 210 mm
• WiFi control: Yes
• Bluetooth: Yes
• Ionization and UV lamp: Yes
• Full tank alarm: Yes
• Automatic defrosting: Yes
• Continuous drainage: Yes
• Parental lock: Yes
• On/Off timer: Yes
• Transport wheels: Yes
• EAN: 5905910416864
• Warranty: 24 months
• Maximum area of the room: 50m²

1 Dehumidifier Mission Air® COREDRY 20L - 1 pc.

2 Condensate drainage hose - 1 pc.

3 Manufacturer's packaging - 1 pc.

4 User manual - 1 pc.

✔ SmartClimate™ WiFi - control the dehumidifier from anywhere through the app on your phone. Requires a permanent connection to the router in the 2,4 GHz band and the free Mission Air application, available on Google Play and the App Store. When connected to power, the device goes into pairing mode for 3 minutes. You can call the activation again by holding down the TIMER button for 5 seconds. Pairing also supports Bluetooth.

✔ AutoSense™ Humidity - set the target humidity, and the dehumidifier itself watches the level around the clock. Setting range from 35 to 90%. When the humidity in the room is equal to or lower, the device interrupts drying and the Run light begins to flash. When it rises again, the dehumidification starts automatically. The device remembers the settings after the power goes out.

✔ DualDrain™ - the choice between a tank and a continuous drain. The protection stops working when the tank is filled and displays the E5 code, and you can see the water level through the indicator on the front. Alternatively, connect the hose to the drain port on the back of the housing and guide the water gravitationally to a constant drain. The drainage outlet must not be higher than the outlet of the device, and the hose must not be twisted.

✔ AutoDefrost™ - automatic defrosting keeps you working in cooler rooms. When frost is formed on the evaporator, the device goes into defrost mode. The compressor then stops, the defrost light comes on, and after the process is completed, the work returns to dehumidification without your participation.

🏚 House owner with basement. The smell of moisture at the bottom persists throughout the year. The device on wheels moves between levels, and the connected hose drains water on an ongoing basis and frees you from walking on the tank. You set the target humidity once, the rest is done by automation.

👨 👩 👧 Family drying laundry at home. The laundry dries for two days and leaves a musty smell. The capacity of 20 liters per day and the highest of the three fan gears reduce this time to several hours. You can also turn on the ventilation mode itself when the humidity is already low.

🔧 House owner after flooding. After the installation failure, the first day counts. Connect the hose to a constant drain and leave the unit overnight, without guarding the tank. After filling the tank, the work will stop on its own anyway, and the E5 code will appear on the display.

🌙 Sleeping lightly. The declared noise level is 43 dB. On the lowest of the three fan gears, the device can work in the bedroom all night, and after the power goes out, it returns to the remembered settings.

🌀 A person sensitive to musty smell. High humidity promotes mold in corners and grout. The Cleanup button triggers ionization and UV lamp, so you dry and refresh the air at the same time. The display shows the current humidity in the room.

🧱 House owner under construction or after renovation. Plasters and spouts give off water for weeks. You set the target humidity in the range of 35 to 90%, and the device turns itself on and off around the clock. Wheels and handle allow you to move them between rooms during work.

📱 A person working outside the home. Settings need to be changed when no one is there. The Mission Air app and 2,4 GHz home WiFi allow you to do it from your phone from anywhere. The on and off timer will schedule work for hours of cheap tariff.

👶 Parent of young children. The panel at the height of the hands tempts to play. The parent lock closes the humidity setting and working status, so accidentally pressing will not change anything. Ecological factor R290 does not destroy the ozone layer.

Effects you will feel in everyday use:

✔ Moisture ceases to be something you think about - you set the target once, and the device watches it itself around the clock.

✔ Laundry dries faster in the room and without the smell of mustiness, so you do not have to hang it on radiators or open windows in winter.

✔ After flooding, you have a tool on hand for intensive drying, instead of waiting for the walls to give water themselves.

✔ You can read the current humidity from the display on the front, and when you are not at home, you will check it and change the setting from your phone.

✔ You do not have to remember to empty every day - either the sensor will stop working at a full tank, or the water drains by itself.

✔ In the bedroom you will set the lowest of the three fan gears, and the declared noise level is 43 dB.

✔ You can move the device on wheels between rooms instead of keeping them in one place throughout the season.

✔ You can pull out the filter in one motion and rinse with clean water, so it takes a few minutes every two weeks to maintain full performance.

❓What if I forget to empty the tank?

💪Nothing will spill. After filling the tank, the device stops working and displays the E5 code. If you want to eliminate this problem permanently, connect the hose to the drain port and run the water gravitationally to a constant drain. The drainage outlet must not be higher than the outlet of the device, and the hose must not be twisted.

❓What if the dehumidifier suddenly stops collecting water?

💪The most common causes are a clogged filter, a blocked air inlet or outlet, or too low temperature and humidity in the room. Also check if the humidity setting is not higher than the current reading, because then the dehumidifier has nothing to do. If frost appears on the evaporator, the device itself goes into defrost mode and returns to work after its completion.

❓What if the device does not start immediately after switching on?

💪 It's a security, not a glitch. At first start-up and after each on-off cycle, a 3-minute compressor protection delay applies. During this time, the Run light flashes, and after three minutes, the work starts normally.

❓What if the code appears on the display?

💪E5 means a full tank, just empty it. E8 is a protection against too high temperature, the device will resume operation itself when the temperature drops. E1 and E2 indicate sensor failure, temperature and humidity respectively. With these two, do not open the case, just submit a complaint via the service form, because the product is covered by a door-to-door warranty and the courier will collect it at our expense.

❓How to set the target humidity?

✅Press the humidity setting button to enter the setting mode, and select a value from 35 to 90%. If you do not press any button for 5 seconds, the setting will save itself and the display will return to showing the current humidity in the room. The device also remembers the setting after the power goes out.

❓What is the difference between dehumidification and ventilation?

✅Button Mode you choose dehumidification or ventilation itself. In dehumidification mode, the device monitors the setting: when the humidity drops to the set value, the dehumidification stops and the Run light begins to flash. When the humidity increases, the work starts automatically. You set the fan speed independently, on one of three levels.

❓Can I connect a permanent drain?

✅Yes. Connect the hose to the water drain port on the back of the housing and guide it to a constant drain. The drainage outlet shall not be higher than the outlet of the device and the hose shall not be twisted or submerged in water. Do not drive it near elements with a temperature above 60 °C.

❓What happens when the tank fills up?

✅The device stops working and displays the E5 code. Turn them off with the button, slide the tank out, empty, wipe and slide them back in, then restart. Do not remove the tank during operation.

❓Why does the dehumidifier not start immediately after turning it back on?

✅Protective operations 3-minute compressor delay. During this time, the Run light flashes. After three minutes, the device will resume drying itself. It's a system security, not a glitch.

❓How often should I clean the filter?

✅Clean it every two weeks during use. Grab the filter and pull outside, rinse with clean water, air dry in a shaded area and put back in. Do not use corrosive chemicals and do not dry the filter in the sun, as it may deform. A clogged filter significantly reduces dehumidification efficiency.

❓How does the timer work?

✅Press the Clock/Timer button twice to set the current time, three times to set the delayed on, four times to set the delayed off, and five times to exit the clock mode. Set the hour and minute with the up and down buttons. After 5 seconds without pressing, the setting saves itself.

🏚 House with basement and laundry

Moisture gathers downstairs and travels higher. You can move the device on wheels where it is the worst, and the hose connected to the drain port on the back of the case frees you from going for the tank.

🧺 Drying laundry in the apartment

Hanging laundry increases humidity and prolongs drying. With a capacity of 20 liters per day and the highest of the three fan gears, laundry dries in a few hours, without hanging it on radiators and without opening windows in winter.

💧 After flooding or cracking the pipe

What matters is the first day. Set the highest fan gear and connect the hose to a constant drain to leave the unit unattended overnight. If it works on the tank, once it is filled, it will stop on its own and show the code E5.

🌙 Bedroom in the heating season

Heating dries the air unevenly, and moisture condenses on the windows. The declared noise level is 43 dB, so at the lowest gear the device can work throughout the night. When the power goes out, it returns to the remembered settings.

👶 Room with small children

The panel at the height of the hands tempts to play. The Parental Mode/Lock button turns on the lock, which closes the humidity setting and working status, so accidentally pressing anything will not change anything.

❌ The lower I set the humidity, the healthier at home.

✅ You can’t, and that’s good. The lowest setting in this device is 35%, and for an apartment a reasonable range is 40 to 60%. Dry air irritates the airways, electrifies fabrics and harms wooden furniture and floors. The goal is a reasonable measure, not an extreme.

❌ The dehumidifier and moisture absorber with granules do the same.

✅ These are two different mechanisms. The condensing dehumidifier cools the air on the evaporator and condenses water from it, collects it into the tank or drains it with a hose, and maintains the humidity level relative to the setting you have chosen.

❌ The dehumidifier will work in an unheated garage in winter.

✅ It will work, but much weaker. The efficiency of condensing dehumidification decreases with temperature, and frost forms in the coolness on the evaporator. The device then goes into automatic defrosting, during which the compressor stops and does not collect water. In a heated room, the effect is clearly better.

❌ The filter is enough to clean once a season.

✅ The recommended rhythm is every two weeks during use. Dust on the filter reduces airflow and reduces efficiency, and a clogged filter is the first thing to check when the dehumidifier stops collecting water. You can pull out the filter in one motion, rinse with clean water and dry it in a shaded place.

1 Setting

Place the dehumidifier on a hard, even surface, with free space around the air inlet and outlet. Do not add it to the wall or pawn it with furniture, because it will suck up its own dried air. Keep away from heat sources and places exposed to splashes.

2 Inclusion

Connect to a grounded socket. When the power is connected, there is a 3-minute compressor protection delay, during which time the Run light flashes. It's normal, not a glitch. Close the windows and doors, because with the dehumidifier open, it fights the entire building.

3 Humidity and mode

Press the humidity settings button and select a value from 35 to 90%. After 5 seconds without pressing, the setting will save itself and the display will return to its current humidity. With the Mode button, you choose dehumidification or ventilation itself.

4 Water

Decide how you drain the condensate. On the tank you do nothing, after filling the device will stop and show the code E5. With continuous operation, connect the hose to the drain port on the back of the housing and guide it down to a constant drain, without bends and without dipping the tip. The outlet must not be higher than the outlet of the device.

5 Convenience

With the fan speed button you select one of three levels. The Cleanup button turns on the ionization and UV lamp. With the Clock/Timer button, you set the delayed on and off. Parental lock turns on the Parental Mode/Lock button. Control from your phone: Mission Air app, 2,4 GHz WiFi network, pairing mode for 3 minutes when connected to power.

By choosing Mission Air products, you get the Mission Air SHIELD package. It is an additional after-sales care, thanks to which you can be sure of peaceful and comfortable use of the purchased device.

Specifications