Suvirinimo aparatas SHERMAN DIGIMIG 200 HIT 200A 4in1 su skydeliu

Trumpai apie prekę

Prekė: Suvirinimo aparatas SHERMAN DIGIMIG 200 HIT 200A 4in1 su skydeliu. Kategorija: Inverteriniai suvirinimo aparatai.

• Gamintojas: no brand
• Modelis: MIG 200 HIT

🥽 Welding machine and visor in one package – eye protection from the first weld 🥽

The most common mistake with the first purchase is the welder without visor. Here the mask goes in the same carton – you do not have to look for it or buy it in a hurry.

Sherman DIGIMIG 200 HIT selects the parameters synergy: you set the material and diameter of the wire, and the device sets the rest. You weld MIG/MAG in a gas shield, FLUX with self-shielding wire and MMA with an electrode; you buy a TIG cylinder and handle when you need them.

⚙ Technical data and power requirements

One phase 230 V, circuit protected on 25 A – ordinary installation is enough.

• ✅ MIG/MAG 200 A, MMA 180 A, TIG 200 A, duty cycle 60%

• ✅ Power consumption 4,8 / 4,9 / 3,6 kVA (MIG/MAG, MMA, TIG)

• ✅ MIG welding voltage 15,5-24 V, idle 65 V

• ✅ Wire 0,6-1,0 mm, feed 2-14 m/min, spools 100 and 200 mm

• ✅ IGBT, sockets 35/50, IP21, fan

• ✅ 10,3 kg, dimensions 43,6 x 21,5 x 32,4 cm – you can easily move it to another place

🏷 Nameplate – parameters on the device

All data is stamped on the housing, not only in the description – you can compare it before the first welding.

• ✅ Model DIGIMIG 200 HIT, standard EN IEC 60974-1

• ✅ Power supply 230 V, 50 Hz, protection degree IP21

• ✅ Operating cycles and currents for each method – MIG/MAG, MMA and TIG

⚡ Features that make a difference at the beginning

• ✅ Synergy – you don’t guess the current and voltage

• ✅ SPOT 0,1-20 s – repeatable point on the sheet

• ✅ 2T/4T – long weld without holding the button

• ✅ Inductance adjustment – soft arc under thin sheet metal

• ✅ Hot Start, Arc Force, VRD – the electrode catches the arc and does not stick

• ✅ Gas Test, fast wire extension, burning 0-10 s

🎛 Panel up close

• ✅ Two displays – voltage and current or wire feed speed

• ✅ Choosing the method and diameter of wire diodes, without browsing the menu

• ✅ 2T/4T and SPOT modes at hand

🔌 Two handles included – MIG/MAG and MMA

There are two handles in the carton, which is two methods ready immediately. The mass cable is not the third method – it closes the current circuit and is needed for each of them.

• 🔥 MIG/MAG MB15 holder – 3 m – for wire welding: in cylinder gas shield (MIG/MAG) and self-shielding wire (FLUX)

• ⚡ Electrode holder – 2 m – for wrapped electrode welding (MMA)

• 🔗 Mass cable with clamp – 2 m – is not used for welding, but closes the circuit; a certain contact is a condition for a stable arc

• 🔩 TIG Lift device supports, but TIG handle needs to be purchased – it is not included in this set

• ✅ 35/50 sockets – market standard, accessories can be purchased in any welding shop

SEE THE VIDEO PRESENTATION OF THE DEVICE

➡ Paste into browser: https://youtu.be/r0lKxCMYMu4 Video presentation of the manufacturer. The video shows the Sherman DIGIMIG 200 HIT welding machine at work – panel, wire feeder and device operation.

🎯 For whom this version

• 🎓 First welding machine – with eye protection immediately, without paying extra for gas

• 🔧 Workshop – profiles, frames, structural repairs

• 🏡 Home and garage – gates, fences, minor alterations

• ⚡ When you already have a cylinder – you do not pay for gas and reducer twice

📏 Feeder and wire – what enters the chamber

• ✅ metal feeder, 2-roll – guides the wire evenly, without slipping on the roll

• ✅ 0,6-1,0 mm wire – steel, aluminium or self-shielding wire

• ✅ Spools 100 mm and 200 mm – small for small jobs, large for longer work

• ✅ Feeding speed 2-14 m/min, wire burning time 0-10 s

🔩 Close-up wire feeding mechanism

• ✅ Guide and drive roller – hence the wire goes to the handle

• ✅ Wire diameter 0,6-1,0 mm, feed speed 2-14 m/min

• ✅ Quick wire extension pushes it through without arcing

🔧 Connections and switch

• 🔌 Gas connector on the back panel – you connect the hose from the reducer when you weld in the gas shield

• ⚡ Network switch ON/OFF and right next to the nameplate

• 💨 Fan cooling, protection level IP21

• ✅ Without gas, you weld using the FLUX method – welding with self-shielding wire, the cylinder is then not needed

📦 Set includes

• ✅ Welder Sherman DIGIMIG 200 HIT

• 🥽 Self-tinting visor Weldman FALCON True Color

• ✅ MIG/MAG holder MB15 – 3 m

• ✅ Electrode holder – 2 m

• ✅ Bulk cable with clamp – 2 m

• ✅ User manual in Polish and warranty card

🔎 Compare offers before you buy

The same welding machine is sometimes sold in different sets. Check out these points in each listing you compare.

• 🥽 Is eye protection included? In the carton lies the Weldman FALCON True Color visor with optical class 1/1/1/2, with grinding mode – you do not buy it separately.

• 🔌 How many handles are included? Here you get MIG/MAG handle MB15 3 m, electrode handle 2 m and mass cable 2 m – MIG/MAG, FLUX and MMA without buying accessories.

• ⚙ What is the wire feeder? Metal, 2-roll – leads the wire evenly and without slipping.

• 🔦 Does the feeder compartment have lighting? It has its own lamp with LIGHTING ON/OFF switch – you can also put the spool in a dark corner of the workshop.

🥽 Weldman FALCON True Color visor

The filter darkens by itself when the arc is lit, so you do not lift the cover between the welds.

• 🎨 TRUE COLOR – more natural colours, easier to assess the lake

• 🔎 Optical class 1/1/1/2

• ⚙ For MIG/MAG, TIG and MMA, with grinding function

• 🔋 photovoltaic cell with replaceable battery

• 🎯 4-arm header, adjustable – adjust the circumference and angle

🔦 Illumination of the feeder chamber

There is a lamp in the chamber with the LIGHTING ON/OFF switch – you put on a spool and thread the wire without shining your phone.

• 🔦 Light switch right next to the feeder mechanism

• ✅ Metal feeder 2-roll, spools 100 mm and 200 mm

• ✅ On the inside of the flap there is a parameter selection table – pulls when changing the material

❓ Frequently Asked Questions

Is there a gas cylinder included?

✅ No. You weld using the FLUX method with self-shielding wire or MMA electrode, and after buying the cylinder also MIG/MAG.

Is the visor suitable for grinding?

✅ Yes, it has a separate grinding mode.

What wire goes into the feeder?

✅ 0,6-1,0 mm, 100 and 200 mm spools.

Is there a cylinder chassis?

✅ No – there is no wheelchair in this version. If you need it, choose a set with a chassis.

Is there a TIG handle?

✅ No. The device supports TIG Lift, but you buy the handle separately.

Specifications