Suvirinimo valytuvas WELD CLEANER MAGNUM SUPER CLEANER MAX su dviem talpomis, 230V

Trumpai apie prekę

Prekė: Suvirinimo valytuvas WELD CLEANER MAGNUM SUPER CLEANER MAX su dviem talpomis, 230V. Kategorija: Inverteriniai suvirinimo aparatai.

• Gamintojas: Magnum
• Modelis: SUPER CLEANER MAX / DUAL TANK

SUPER CLEANER MAX DUAL TANK

Device for electrolytic cleaning of stainless steel after welding.

Removes discoloration without mechanical interference and without the risk of damage to the surface.

The electrochemical etching process used allows you to restore the original appearance of the material with a much shorter working time.

Key advantages

• continuous electrolyte delivery system – higher work efficiency
• two independent tanks (2x2 l): electrolyte + water
• rapid rinsing of the system after work
• AC / DC modes – adapting to the type of dirt
• TURBO function for removing difficult discolorations
• smooth regulation of power and liquid flow

Functions of the device

• electrochemical cleaning of stainless steel
• surface renewal after welding
• regulation of cleaning power
• regulation of liquid outflow
• choice of operating mode: brush / spatula
• Current mode selection: AC/DC
• patented handle with TURBO function
• protection system:

  overload

  short-circuit

  thermal

In the picture on the left you can see the condition before cleaning, on the right after cleaning with this device.

The working handle has two buttons on the handle, marked with numbers 1 and 2.

Pressing button 1 only triggers the outflow of liquid (electrolyte or water - depending on the setting of valve 9), with the outflow speed set by knob 10.

The current at the output of the handle appears immediately after starting the device and is independent of whether button 1 is pressed or not. The current value is determined by a knob 5. Pressing button 2 turns on the TURBO function, but does not activate the liquid outflow!

In short:

* Device turned on, no button pressed: the liquid does not flow out, the current at the outlet lasts all the time, according to the settings on the panel.

* Device on, button 1 pressed - pump feeds liquid. Button 1 unpressed - pump does not give liquid. The current lasts all the time, according to the settings on the panel.

• Device on, button 2 pressed - pump does not give fluid, active current mode TURBO. When the button 2 is released, the current returns to the current settings.

The given numerical markings are visible in the description of the device panel in the manual.

Electrolyte

The device can be poured with any liquid intended for electrolytic cleaning. You can use powders to make a solution yourself or ready-made liquids. However, it should be remembered that the speed of cleaning and the final effect largely depend on the quality of the electrolyte used.

The capacity of the electrolyte tank is 2 liters. The second tank, with the same capacity, is designed for water to rinse the wires.

Working handle tips

The work handle can be armed with a carbon brush or spatula. The set includes brushes and spatulas in two sizes. Small brush ø9 mm is used to clean corners and narrow welds with low current. Large brush ø11 is used to clean flat surfaces e.g. wide butt welds. In turn, spatulas are used to quickly clean flat surfaces with high cleaning power.

The individual diameters of the carbon brushes correspond to individual ceramic sleeves. One ceramic sleeve with a hole diameter of 20mm is provided for spatulas. The bushings do not have a thread - they are pushed on and off the body of the working handle. Brushes and spatulas are screwed into the body of the working handle - they should be tightened with little force.

TURBO function

SUPER CLEANER MAX / DUAL TANK has a patented working handle with buttons described in numbers 1 and 2. Pressing button 1 triggers the electrolyte flow. Pressing button 2 activates the current TURBO mode, but without electrolyte outflow.

If there are stains on the cleaned material that can not be removed in normal mode, they should be moistened with electrolyte, then press and hold the button 2 - cleaning with great force, the stains temporarily may become darker. Then release the TURBO function button and continue cleaning in normal mode - the stains will be removed.

TURBO mode should be used with caution, because the abuse of this function results in accelerated wear of the tips used (brushes and spatulas).

After the work is completed, the device should be switched to the water outflow and rinsed abundantly to remove the remaining electrolyte from the working handle and its wires. The workpiece should also be washed off with water and dried.

Included with the SUPER CLEANER MAX / DUAL TANK are:

• cable with mass clamp 1 pc.
• working handle, 3 m 1 pc.
• set of replaceable carbon brushes:- ø 9 mm + ceramic sleeve 1 set. - ø 11 mm + ceramic sleeve 1 set.
• set of interchangeable, flat spatulas:- 15 mm (spatula + cloth) 1 set. - 40 mm (spatula + cloth) 1 set. - common ceramic sleeve (ø20x65 mm) 1 pc.
• Working handle bracket 1 pc.
• instruction manual 1 pc.

Specifications