Tvenkinio vandens siurblys AQUARIUM ECO CTP-2800, 3000 l/h, 10W

Trumpai apie prekę

Prekė: Tvenkinio vandens siurblys AQUARIUM ECO CTP-2800, 3000 l/h, 10W. Kategorija: Siurbliai.

• Gamintojas: no brand
• Modelis: hardware-store
• Galia: 10 W

Pond Pump Eco Filter Pump, Garden Pond Pumps Water Pump Pond Pump with Carp koi Stream Pump Pond Pump, Quiet Aquarium Pump Submersible Pump, Amphibia Pump for Ponds Garden Irrigation

The housing is made of ABS plastic, and the spindle and sleeve are made of high-strength ceramic, thanks to which it is characterized by a long service life and high corrosion resistance. Motor coil made of 100% copper wire is characterized by good quality and high efficiency.

The flow control valve can be adjusted to control the amount of water per unit time. The turbine is designed to enhance the sealing performance and increase its stability. There is no filter in the pump. The filter cover allows you to effectively filter out impurities, so that the water is not easily blocked. Thanks to this, filtration is more accurate, the service life is extended, and the maintenance time is also shortened.

It can be used simultaneously for complete immersion in fresh and salt water, suitable for all marine and freshwater aquariums, ponds, rock gardens, garden irrigation, fountains. The pump can be used to filter ponds, power rock gardens with water, rock garden landscapes, water gardens and filter aquariums.

The inflow can be adjusted according to your needs to adjust the outflow rate.

Double protection guarantees the safety of customers during use and prevents the device from disconnecting due to operating vibrations.

The ceramic turbine shaft is characterized by high flow rate, low energy consumption, high pressure and is designed for fresh/sea water.

The streamlined handle is easy to operate and the ABS resin housing is resistant to high temperature and wear, making it suitable for diving and land use.

There is no filter in the pump，Thanks to the filter cover, fine dust and impurities can be effectively filtered, the water is strongly clogged, so the filtration is much more accurate, the service life is strengthened, and the maintenance time is reduced.

Under no circumstances should the water pump work without water (dry operation). Otherwise, the pump axles would be damaged.Before turning on，The pump body must be filled with clean water.

The pump should not be placed directly in the mud on the ground. It should be raised. Using it in a murky aquatic environment will shorten its lifespan. If the aquatic environment is cloudy, it is recommended to clean the filter cover and internal equipment every 2 weeks. Normally, it should be cleaned every 4 weeks.

Product information:

- Energy-efficient

- Ceramic axle without wear

- Easy cleaning

- Rated voltage: 220 V.

- Rated frequency: 50 Hz

- Power: 10W

- Maximum head: 2,0 M

- Maximum flow rate: 3000L/H

- Output: 20-25-32mm

- Dimensions: approx. 172x113x126mm

- Cable length: approx. 5 m

Scope of delivery:

1 x 3000 L/H 10W ECO joint pump CTP-2800

2. We doubled the cable length based on factory settings. to adapt to more use environments

3. Please make sure the length of the cord is sufficient for you before placing your order.

IMPORTANT:

Do not allow the pump to work dry - working outside the water (dry work) can lead to irreparable damage in a very short time!

No disassembly tools, more convenient and faster：

1. adjustable flow rate

2. turn the water filter cover towards the arrow

3. pull the buckle towards the arrow

4. turn the wheel chamber towards the arrow

5. pull out the rotor to clean and replace it

6. sealing ring mounting position

Working environment:

Make sure that the pump is immersed in water and 20 cm below the water level during use, and the water temperature should be 4-35℃. Avoid operating the product in an environment without water, as this can cause the engine to burn out.

After dismantling and cleaning the water pump, the inside of the engine rotor must be wiped clean or air-dried, and then installed according to the appropriate steps before turning on.

Before turning on，The pump body must be filled with clean water. When using the pump function, use the water inlet pipe to inject water into the pump body. When there is running water in the outlet port, it can be turned on.

Turn off the power, then remove the pump body directly from the pond, do not pull the pump power cord.

Specifications